suspension

We all know these trailers are built with a slight bend in the axle to give some camber to the tires. On the above camper trailer, If I string a line along the bottom edge of the axle from end to end, how much gap should I see in the center?

We have a 2024 Jayco Eagle 321rsts 5er. It has a MORryde CRE3000 suspension on it. In talking to other 5er owners, several have said they either had 5er's with shocks on the axles or have added shocks to the axles. All have stated that it really helps how the 5er pulls and that it eliminated a...

I am wondering how many of you have added a Safe T Plus steering stabilizer to your rig and if you feel it’s an absolute plus to have

Has anyone tried the “rust converter” paints on their TM torsion rods? I’ve noticed the rods on my 2009 2720 SL have about 5 times a thick layer of rust compared to the frame members.’d like to stop the rust but am concerned that any cracks in the converter paint (due to the rod twisting)!will...

We own a 2021 3121RL Montana. I have a bent wet bolt on the right rear hanger and am posting a couple pictures showing it. The hanger that the leaf spring is attached to with this now bent wet bolt was just replaced in the spring of 2025 and reinforced with gussets and a crossbeam after the...

B and B+ RVs are generally built on Sprinter, Transit or Ram van chassis. These have a ground clearance of 6 to 7.5 inches. On highway this is not an issue , generally, but with steep driveways or big differences between road surfaces can lead to bottoming out. Adding something below, like a...

Hello, poking around a bit and saw this plug hanging down on the drivers side near the leaf springs. Anyone familiar with it? Is it a test port of some sort? Should I just clean it up with electrical cleaner and put the cap on? Also, appears to be more grease or road grime on the wet bolts and...

My wife has been asking me to improve the suspension on our rig since shortly after we got it. I spent some time looking through forum posts regarding suspension upgrades, and decided to start with Sumo Springs. They are relatively inexpensive and they looked like something I could install...

Hello all. I recently acquired 1994 Chevy Minnie Winnie with the 5.7l motor. It sways and am looking to fix. I looked at the rear leaf springs and they are 5/1, and best can tell are rated to 2850lbs per, so a total of 5700 lbs. My GAWR is 7200 lbs. I am seeing if anyone knows what leaf...

I have a 2025 Entegra Vision 29S and am preparing to go to Utah from NJ 04/13/26 Been looking a many blogs and talking to installers about the choice. Seems that new shocks would give batter results eliminating a portion of bump rattling versus bags. Q? Air or shocks O? If shocks, what model and...

I need to have the alignment checked on my IS. I'm in Central Texas. Anyone have a suggested place to get this done?

Howdy Streamers, I am replacing the axel on my '64 Safari with a dexter #11 and I'm hoping to gain some wisdom from someone who's done this job before. The holes on the original axel are spaced 10" center to center. Would have loved for this to bolt right in but the new axels bolt pattern is...

As first time owners of a MH I am asking some dumb questions I'm sure so bear with me. When we parked our 2025 DS 4369 at our storage facility I hit the manual air dump button on the HWH panel since I was not going to use the coach for a few weeks. 1) Should I do this, not do this or does it...

We have a 2018 classic 30 RQB, I am adding a lift. What is the best lift, 2 or 3 inches? I have to say I’m out dragging the bottom much now.

On our 2022 tiffin open road 34pa the LS Wouldn't bring up the rear suspension up ,was told by support to over ride system which made all 4 corners to go all the way up. We are currently on the road, we lower all the way down every night and in the morning before driving set system to...

Hey all, wondering where you all source parts from. I’ve read that upgrading the nylon bushings to a bronze wet bolt style is an almost necessary upgrade due to nylon wearing out rather quickly. Thanks in advance for any input! 2024 grey wolf 26dbh

2004 Sightseer 30b Work Horse chassis. Can anyone tell me, before I go crawling around, if this has an air suspension? And where would the fill point be? Dontcha hate newbies? LOL

Has anyone done the CRE3000 install on their Montana? Good ? Bad? I know the road master setup is the way to go, but not in my budget at the moment. Also 6 or 7 leaf springs?

I first found ut about Liquid Springs at the Tamps RV show sharing a spot at the Lazy Days booth. They were pretty new at the time and mainy for a gas class A. They had a demo motorhome for test drives. At the time I had nt Country Coach, so it was just a curious thought. This past month I...

Well this may or may not be an approved post. But I spent a decent amount to upgrade to a higher end TT model from our older 2017 Jayflight and have also dealt with the typical working out the bugs since I purchased it on my own. I knew going in that I would have problems when buying new and...

2024 K2 Entegra Anthem 20K miles. Having “no data ABS” “check suspension” “no data-rear suspension mod” plus “not at ride height” intermittent. Rotates through these codes or warnings. Have had the modules replaced and software updated. Clear codes and they come right back after about 20miles...

we bought an unreal SMB a few years ago that had been modded by the first owner at a shop in San Diego that did a Crow style build. Not the build so often seen online with the funky twin shock stabilizers on diesel low tops but a beautiful gaucho build with all the SMB stuff like Starcool and...

Hi all! Had an issue with leaf springs and axel flattening out. Before I left, I had my local dealer service , inspect and repack bearings and check entire suspension system plus do PM on entire trailer. I loaded 2 street glide Harleys in the garage and headed to Sturgis SD from NC last August...

Hi all, I was working in the garage yesterday and noticed that I have a leaf spring hanging free under my van. It's an Entegra Arc (same as Jayco Comet) which is based on a Promaster 136" window van. Looks like the bushing that was supposed to be between the helper spring and the factory...

My 2019 insignia has a problem with air pressure bleeding down in the rear. I took this to a local place who replaced bags and a couple fittings but that did not solve the problem. I took this to spartan Chassis in Michigan since they build the damn thing so that they could fix it. We know...