Temporary Waterproofing for Damaged RV Panels and Missing Generator Door

Thread Summary

Summarized on:
Original Member Title: Best temporary repair
This AI-generated summary may contain inaccuracies. Please refer to the full thread for complete details.
An RVer sought temporary waterproofing for loose rear-wheel-well paneling after striking a concrete post, plus a replacement for a generator compartment door that came completely off. They were considering Gorilla waterproof tape or painter’s tape over putty tape, with concerns about removal when permanent repairs begin. One member cautioned that duct-tape-type products could leave adhesive residue and reported easier removal with electrical tape, suggesting wider PVC vinyl tape as another...
More...

nsmith0526

New Member
Joined
Oct 2, 2026
Posts
3
Location
Indiana
I misjudged a turn (thank you migraine, i shouldn't have been driving) and hit a concrete post. Pulled some paneling loose on the side near wheel well in back and door of generator compartment. What is the best temporary waterproofing fix for a few weeks until we are able to get it repaired? I am seeing gorilla waterproof tape. Painters tape with Putty Tape underneath. But don't want problems taking it off when the final repairs are done. I also need ideas for replacing that darn door. Needless to say I am very angry at myself
 
What year/chassis are you working on?

I think any duct tape based product will end up separating the surface from the glue backing leading to a lot of labor to get the adhesive off what it's on.

Will your other option you mention with a putty knife ruin the finish?

Depending on the size of the crack, I've had good luck using electrical tape. Typically comes off in one piece and not a lot of adhesive left over. But its not very wide. Maybe there's a wide electrical tape/similar product out there.

I did find this. Seems like pvc vinyl tape may be what you need.


Is the generator compartment made of degradable material where water intrusion is an issue, or more metal or fiberglass construction where water doesn't degrade the material?
 
Last edited:
What year/chassis are you working on?

I think any duct tape based product will end up separating the surface from the glue backing leading to a lot of labor to get the adhesive off what it's on.

Will your other option you mention with a putty knife ruin the finish?

Depending on the size of the crack, I've had good luck using electrical tape. Typically comes off in one piece and not a lot of adhesive left over. But its not very wide. Maybe there's a wide electrical tape/similar product out there.

I did find this. Seems like pvc vinyl tape may be what you need.


Is the generator compartment made of degradable material where water intrusion is an issue, or more metal or fiberglass construction where water doesn't degrade the material?
The generator door came completely off. I need a new one.
 
What year/chassis are you working on?

I think any duct tape based product will end up separating the surface from the glue backing leading to a lot of labor to get the adhesive off what it's on.

Will your other option you mention with a putty knife ruin the finish?

Depending on the size of the crack, I've had good luck using electrical tape. Typically comes off in one piece and not a lot of adhesive left over. But its not very wide. Maybe there's a wide electrical tape/similar product out there.

I did find this. Seems like pvc vinyl tape may be what you need.


Is the generator compartment made of degradable material where water intrusion is an issue, or more metal or fiberglass construction where water doesn't degrade the material?
I really appreciate your help!!
 
The generator door came completely off. I need a new one.
Per my generator guy, do NOT run the generator with the door off. Good luck finding one, if it's the older Onan 2.8. I had mine stolen, and lucked out finding a used one. I regret not keeping it when I replaced it with the new 2800i. I could have sold it for a decent amount. The new Onan 2800i has a much more reliable door.
 
Per my generator guy, do NOT run the generator with the door off. Good luck finding one, if it's the older Onan 2.8. I had mine stolen, and lucked out finding a used one. I regret not keeping it when I replaced it with the new 2800i. I could have sold it for a decent amount. The new Onan 2800i has a much more reliable door.
I wonder if it might be possible to get a metal shop to make a replacement. It's mostly just a flat piece of sheet metal. I don't think it would be possible to get those plastic clips that hold it in place done, but maybe something else could be figured out to hold it in place.
 
The plastic clips were a really poor design. The used door I bought had one that was broken, I thing there was a spring inside the clip that went bad, so I used some strong magnets to hold it in place. FYI it's a pretty thick gauge metal. I would use sort of clip similar to these, but be careful where it gets screwed into. Good luck. Amazon.com
 

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top